Concrete floors in
Alabaster
AL
Alabaster is one of the towns we have run tooling in for years, in Shelby County along I-65 south of Birmingham.
Get my free quoteFree quote . No obligation . Fast response
Alabaster and the floors in it
Alabaster is in Shelby County along I-65 south of Birmingham, inside the 100 miles we work out of Huntsville.
Alabaster is largely subdivision homes built largely since the 1990s with attached garages, so the slabs we see there have a family resemblance.
What gets built here follows one of Shelby County’s fastest growing cities, and that decides what needs finishing.
We are often in Pelham, Helena, Calera in the same week, so scheduling around Alabaster is rarely a problem.
The thing that shapes Alabaster is one of Shelby County’s fastest growing cities, and that shows up in the floors.
Flake epoxy goes in most garages. Polished concrete goes in most open commercial spaces. Urethane cement goes where it is wet.
What Alabaster usually asks for
Those are the ones that come up most in Alabaster. Everything else we install is available here too. Every system we install is available here, and the right one is chosen from the slab in front of us rather than from a list.
Flake Epoxy Flooring
In Alabaster, flake epoxy flooring is a frequent answer, largely down to subdivision homes built largely since the 1990s with attached garages.
The chip does real work beyond looks. It builds texture underfoot, and it hides the small variations in a slab that a solid color would put on display.
Flake goes on while the base coat is still wet. We broadcast it to refusal, which means we keep throwing chips until the floor will not take any more, then scrape back the loose material once it has set.
The texture gives you grip when the floor is wet, without feeling rough. Chips and scuffs disappear into the pattern instead of standing out.
More on flake epoxy flooring
Polished Concrete
With one of Shelby County’s fastest growing cities driving the town, polished concrete earns its place in Alabaster.
How the floor ends up looking depends on how deep we go. A light grind leaves the surface close to how it was poured. Going deeper opens the slab and exposes the sand, then the stone, so you get a terrazzo look out of concrete that was already there.
Polishing is mechanical, not a coating. We run diamond tooling across the slab in steps, each one finer than the last, and the gloss comes from the concrete closing up rather than from anything we put on it.
Nothing to reapply. There is no wax and no topcoat to peel. It reflects light, so a dim warehouse or basement gets noticeably brighter without new fixtures.
More on polished concrete
Epoxy Flooring
Epoxy flooring comes up in Alabaster because the stock here is subdivision homes built largely since the 1990s with attached garages.
Cracks and pits get filled with a repair product compatible with what goes over it, because a patch that flexes differently than the coating telegraphs through the finish within a season.
Epoxy is two parts that get mixed on site and start curing the moment they meet. That chemistry is why prep timing matters and why a coating put down over a sealed or dusty slab lets go later.
Seamless means there is no grout line or seam for dirt to collect in. Color and flake are chosen up front, so the floor matches the room instead of fighting it.
More on epoxy flooring
The slab underneath
Anything poured in the last twenty years around Alabaster is usually straightforward to prepare. Older concrete takes longer to open up, and we price that honestly once we have ground a test patch.
Whatever is on the slab now comes off mechanically before anything new goes down.
Whatever is on the slab now comes off mechanically before anything new goes down.
Sometimes the honest answer is that a slab is not worth coating. If a crack is still moving, if sections have dropped, or if there is water coming up through the concrete with nowhere to go, a coating will fail and take your money with it. We would rather tell you that in Alabaster than sell you a floor twice.
We quote the floor first, in person. Once you accept, the install gets booked as a block rather than squeezed between other jobs, because a resin floor cannot be half finished and left overnight. For a Alabaster job that usually means we hold consecutive days and give you the dates up front.
Clear the room before we arrive. For a garage that means everything off the floor, including shelving feet and anything mounted low on the wall that we need to cut in behind. We can work around a few heavy items, but the more of the slab that is open, the better the edges come out.
Whatever the room is, the sequence does not change: open the concrete, fix what needs fixing, then put down the system the slab will actually hold.
Everything we install
Polishing
Decorative
Restoration
Safety
Do you cover Alabaster?
Yes. Alabaster is in Shelby County and sits inside the 100 miles we run out of Huntsville. Same crew as every other job, and no travel charge for being there.
Which floors suit Alabaster properties?
Around here it is usually flake epoxy flooring, polished concrete and epoxy flooring, because the local stock is subdivision homes built largely since the 1990s with attached garages.
Is commercial flooring available in Alabaster?
It is. Given one of Shelby County’s fastest growing cities, we see everything from back of house wet areas to open retail and warehouse floors around Alabaster.
How soon could you get to Alabaster?
Usually within a few days to look at it. We are often working Pelham, Helena in the same stretch, so fitting Alabaster into a run is normally straightforward.
What does a floor cost in Alabaster?
It depends on square footage, what shape the concrete is in, and how much removal the job needs. We price the floor in front of us rather than working from a rate card.
Can I see one of your floors in person?
Often yes, particularly commercial floors in buildings the public can walk into. Ask when you call.
A floor in Alabaster?
Get Kortni out to look at it. (205) 238-8111.