Concrete floors in
Jacksonville
AL
Floors in Jacksonville come to us through the same door as everything else, a phone call and a look at the concrete.
Get my free quoteFree quote . No obligation . Fast response
Jacksonville and the floors in it
You will find Jacksonville north of Anniston in Calhoun County, and we cover it the same as anywhere else.
What gets poured in Jacksonville is student rentals, faculty neighborhoods and older homes, and the age of a slab changes the prep more than the finish does.
Locally the driver is Jacksonville State University. Floors in those buildings get treated accordingly.
We are often in Anniston, Oxford, Piedmont in the same week, so scheduling around Jacksonville is rarely a problem.
For Jacksonville, Jacksonville State University is the anchor, and the property around it follows.
Garages are the most common residential call. Flake epoxy over a ground slab handles hot tires and dropped tools without complaint.
What Jacksonville usually asks for
Most Jacksonville inquiries land on one of those three. Your floor may point somewhere else, and that is fine. Every system we install is available here, and the right one is chosen from the slab in front of us rather than from a list.
Urethane Cement Flooring
Urethane cement flooring comes up in Jacksonville because the stock here is student rentals, faculty neighborhoods and older homes.
These rooms get integral cove base, so the floor turns up the wall instead of stopping at a joint. There is no seam at the wall line for water to work into.
Urethane cement is a different animal from epoxy. It is thicker, it tolerates moisture in the slab that would blow an epoxy off, and it handles thermal shock, which is the real problem in a kitchen.
It takes hot water, steam cleaning, and caustic wash down chemicals. It can go over slabs with moisture that would fail an epoxy.
More on urethane cement flooring
Concrete Resurfacing
In Jacksonville, concrete resurfacing is a frequent answer, largely down to student rentals, faculty neighborhoods and older homes.
An overlay is a thin layer of polymer modified cement bonded over the slab you already have. Structurally the old concrete keeps doing its job. The overlay gives you a fresh surface to finish.
It is not a fix for a slab that has failed. If sections have dropped or a crack keeps moving with the seasons, that is a subgrade problem and an overlay will mirror it. We say so when we see it.
Far less cost and disruption than tear out and replacement. Surface spalling, scaling, and pitting go away.
More on concrete resurfacing
Polished Concrete
With Jacksonville State University driving the town, polished concrete earns its place in Jacksonville.
A densifier goes down partway through the grit sequence. It reacts with the free lime in the slab and hardens the surface from within, which is what keeps a polished floor from dusting the way bare concrete does.
How the floor ends up looking depends on how deep we go. A light grind leaves the surface close to how it was poured. Going deeper opens the slab and exposes the sand, then the stone, so you get a terrazzo look out of concrete that was already there.
It reflects light, so a dim warehouse or basement gets noticeably brighter without new fixtures. Sweeping and an occasional damp mop is the entire maintenance routine.
More on polished concrete
The slab underneath
What is already on a Jacksonville floor matters as much as the concrete underneath. Paint, glue, sealer and old coatings all come off mechanically first.
Grinding also shows us what the slab is actually like under whatever is on it.
Surface prep is where the money goes on a floor that holds up.
Sometimes the honest answer is that a slab is not worth coating. If a crack is still moving, if sections have dropped, or if there is water coming up through the concrete with nowhere to go, a coating will fail and take your money with it. We would rather tell you that in Jacksonville than sell you a floor twice.
We quote the floor first, in person. Once you accept, the install gets booked as a block rather than squeezed between other jobs, because a resin floor cannot be half finished and left overnight. For a Jacksonville job that usually means we hold consecutive days and give you the dates up front.
Clear the room before we arrive. For a garage that means everything off the floor, including shelving feet and anything mounted low on the wall that we need to cut in behind. We can work around a few heavy items, but the more of the slab that is open, the better the edges come out.
Whatever the room is, the sequence does not change: open the concrete, fix what needs fixing, then put down the system the slab will actually hold.
Everything we install
Polishing
Decorative
Restoration
Safety
How far is Jacksonville from you?
Close enough that it is ordinary work. We are based in Huntsville and cover about 100 miles out, which takes in all of Calhoun County.
Which floors suit Jacksonville properties?
Around here it is usually urethane cement flooring, concrete resurfacing and polished concrete, because the local stock is student rentals, faculty neighborhoods and older homes.
Can you handle a business floor in Jacksonville?
We can. Jacksonville State University means Jacksonville has working buildings, and those floors get specified around how they are cleaned and what runs across them.
When can you start in Jacksonville?
Depends where the schedule is, and we will tell you honestly. Being near Anniston, Oxford means we pass through this part of Calhoun County often.
What does a floor cost in Jacksonville?
It depends on square footage, what shape the concrete is in, and how much removal the job needs. We price the floor in front of us rather than working from a rate card.
Can I see one of your floors in person?
Often yes, particularly commercial floors in buildings the public can walk into. Ask when you call.
A floor in Jacksonville?
The fastest way to get a real number for a Jacksonville floor is to call (205) 238-8111.